Introduction of tunnel automatic car washer

二.Equipment Overview and workflow:

1, Hua Yang brand HY-S9H tunnel continuous automatic car washing machine is mainly used for various cars, small van, SUV model of the appearance of high pressure washing (water knife), spray foam, brushing, spray wax water and dry one time to complete.

2. Work flow:

When the vehicle is sent to the car wash room, the surface of the car is flushed with a fixed high pressure water knife without a blind area, and then the dust particles on the surface of the car are thoroughly cleaned by the spray of foam, the transverse brush and the front brush, so as to protect the surface of the car body to the maximum extent, and then the front water, the middle water road, the back water road and the small brush. Two large abduction arms and two large swing arms wash the side, rear and front of the body, then spray water wax, and finally blow dry through a strong fan to make the surface of the vehicle bright as new. When the vehicle is sent to the exit when the vehicle is sent to the green light, it can drive out.

Four. Equipment technical parameters:

1, applicable models: cars, all kinds of minibus.

2, cleaning size: 5200 (long) *2000 (wide) *2000 (high) (mm)

3, cleaning methods: high pressure washing, spray foam, brush, low pressure cleaning, wax washing, air drying.

4. Car washing speed: 40 / h (continuous car wash)

5, air pressure: 5Kg/cm (optional air compressor: 0.36 cubic / min.)

6. Water use: about 180L/ vehicles

7, machine size: body 13895 (long) *3800 (wide) *3000 (high) (mm) (including import and export lane and corrector)

8, equipment occupation size: 14000 (long) *4000 (wide) *3000 (high) (mm)

9, the size of the roll: 9 sets

10. Wind drying structure: strong fixed air drying system

11, power supply: three phase 380V 25KW (belt fan and air pump)

12, ambient temperature range: 0 C -45 C

13. Total weight of equipment: 7480Kg

Five. The main components of the equipment are:

1, frame structure: (inside and outside double frame structure, using GB 235 steel plate)

(1) cold plating + spray plastic parts: 2, 10 outer cabinet posts, 2 Export boxes, 8 upper beams, 8 indoor columns, 12 ground pull beams, 2 imported square boxes, 4 inner pull beams, 2 imported decorative doors, 1 electric boxes and 1 gas boxes.

(2) top tile 14, tile eaves 6 (long) +4 root (short), square steel tube 2 (large) +4 root (middle) +4 root (small), tempered safety glass 12 pieces.

2. Track structure:

Conveyor track 9 section (hot plating), corrector 2 sets (hot plating), large chain 30, reducer and motor 1 sets.

3. Roll brush structure:

Cross brush 1 sets, crank arm brush 2 sets (hot plating), swing arm 2 sets (hot plating), small vertical brush 4 sets, reducer and motor 9 sets, brush and brush shaft body 9 sets.

4. Fan system:

One set of left and right side wind machines, 2 sets of winder.

5. Water system:

(1) 1 sets of high-pressure multistage pumps, 1 sets of high-pressure water pipes, 12 high-pressure nozzles (2025), 4 high-pressure steel hose, 1 sets of high pressure drainage and water blowing devices.

(2) 1 low pressure diving pumps, 1 sets of front, middle and rear Waterways (3012 of the nozzles 36), 1 sets of low pressure busbars (with water blowing function).

(3) 1 foam water wax pumps, 1 foam wax buckets each with liquid level detection function, 2 foam nozzles each, which can be used to adjust the amount of water flow by the ball valve.

6. Air control system:

Cross brush cylinder (TGU50*500) 2 sets, small brush cylinder (TGM32*150) 4 sets.

The crank arm cylinder (TGU40*150) 2 sets, the swing arm cylinder (TGU40*300) 2 sets, the TG solenoid valve 6, the CR pressure reducing valve 10, the CV one-way valve 9, the filtration two union 1.

7. Electrical control system:

(1) electric cabinet: Japan MITSUBISHI programmable controller (FX3U-80MR-001) 1, Taiwan nylon touch screen (MT6103iP) 1, Schneider AC contactor + thermal overload relay 15 sets, safety isolation control transformer (JBK3 - 400) 1, DC24V switch power (Hongkong Ming) 1, phase sequence protection relay (XJ3-G) 1, total Power leakage circuit breaker, air switch and insurance.

(2) peripheral: photoelectric switch to the United States Bonner 1 sets (big) +2 sets (small), proximity switch 2 sets, brush waterproof motor (full sealed) 9.