Tunnel automatic car washer

Tunnel automatic car washer

1. Equipment Overview and workflow:

1, Hua Yang brand HY-S9H tunnel continuous automatic car washing machine is mainly used for various cars, small van, SUV model of the appearance of high pressure washing (water knife), spray foam, brushing, spray wax water and dry one time to complete.

2. Work flow:

When the vehicle is sent to the car wash room, the surface of the car is flushed with a fixed high pressure water knife without a blind area, and then the dust particles on the surface of the car are thoroughly cleaned by the spray of foam, the transverse brush and the front brush, so as to protect the surface of the car body to the maximum extent, and then the front water, the middle water road, the back water road and the small brush. Two large abduction arms and two large swing arms wash the side, rear and front of the body, then spray water wax, and finally blow dry through a strong fan to make the surface of the vehicle bright as new. When the vehicle is sent to the exit when the vehicle is sent to the green light, it can drive out.

Two. Equipment technical parameters:

1, applicable models: cars, all kinds of minibus.

2, cleaning size: 5200 (long) *2000 (wide) *2000 (high) (mm)

3, cleaning methods: high pressure washing, spray foam, brush, low pressure cleaning, wax washing, air drying.

4. Car washing speed: 40 / h (continuous car wash)

5, air pressure: 5Kg/cm (optional air compressor: 0.36 cubic / min.)

6. Water use: about 180L/ vehicles

7, machine size: body 13895 (long) *3800 (wide) *3000 (high) (mm) (including import and export lane and corrector)

8, equipment occupation size: 14000 (long) *4000 (wide) *3000 (high) (mm)

9, the size of the roll: 9 sets

10. Wind drying structure: strong fixed air drying system

11, power supply: three phase 380V 25KW (belt fan and air pump)

12, ambient temperature range: 0 C -45 C

13. Total weight of equipment: 7480Kg

Three. The main components of the equipment are:

1, frame structure: (inside and outside double frame structure, using GB 235 steel plate)

(1) cold plating + spray plastic parts: 2, 10 outer cabinet posts, 2 Export boxes, 8 upper beams, 8 indoor columns, 12 ground pull beams, 2 imported square boxes, 4 inner pull beams, 2 imported decorative doors, 1 electric boxes and 1 gas boxes.

(2) 14 roof tiles, 6 (long) + 4 (short), 2 (large) + 4 (middle) + 4 (small), 12 toughened safety glass.

2. Track structure:

Conveyor track 9 section (hot plating), corrector 2 sets (hot plating), large chain 30, reducer and motor 1 sets.

3. Roll brush structure:

One set of horizontal brush, two sets of crank arm brush (hot plating), two sets of swing arm (hot plating), four sets of small vertical brush, nine sets of reducer and motor, nine sets of brush and brush shaft.

4. Fan system:

One set of left and right side wind machines, 2 sets of winder.

5. Water system:

(1) High-pressure multi-stage pump 1, high-pressure water pipe assembly 1, high-pressure nozzle (2025) 12, high-pressure steel wire hose 4, high-pressure drainage, blowing device 1.

(2) One low-pressure submersible pump, one set for the front, one set for the middle and one set for the rear waterways (36 nozzles containing 3012), and one set for the low-pressure confluence row (with blowing function).

(3) 1 foam water wax pumps, 1 foam wax buckets each with liquid level detection function, 2 foam nozzles each, which can be used to adjust the amount of water flow by the ball valve.

6. Air control system:

Cross brush cylinder (TGU50*500) 2 sets, small brush cylinder (TGM32*150) 4 sets.

Two sets of crank arm cylinders (TGU 40 * 150), two sets of swing arm cylinders (TGU 40 * 300), six sets of TG solenoid valves, 10 CR pressure relief valves, nine CV one-way valves, and one filter two-piece.

7. Electrical control system:

(1) electric cabinet: Japan MITSUBISHI programmable controller (FX3U-80MR-001) 1, Taiwan nylon touch screen (MT6103iP) 1, Schneider AC contactor + thermal overload relay 15 sets, safety isolation control transformer (JBK3 - 400) 1, DC24V switch power (Hongkong Ming) 1, phase sequence protection relay (XJ3-G) 1, total Power leakage circuit breaker, air switch and insurance.

(2) Peripheral: (1) Photoelectric butterfly switch using the United States Bonner 1 set (large) + 2 sets (small), proximity switch 2 sets, brush waterproof motor (fully sealed) 9.